This was a really cool project and seems to be successful. I’m hoping to continue and try some more interesting forms beyond text. I think cutting-edge fabrication technology is at it’s best when combined with established/non-digital techniques–it’s the best of both worlds!

This pour took place at the Butler Street Foundry in Chicago.

Laser-cut Form for Bronze Casting

The Final Product: A Cast Bronze Plaque

A Deep Raster Engraving With a Tapered Shoulder Makes for a Great Plaque Form

A Two-part Sand Mold Will Recieve the Molten Bronze

Casting Sand Packed into the Mold Holds an Impression of the Laser-cut Form

Casting Sand is a Mixture of Sand & Clay; Imagine the Best Sand-Castle Sand, Times Ten

A Gas Furnace is Used to Melt the Bronze

Solid Bronze Goes into the Furnace to Melt

Solid Bronze Goes into the Furnace to Melt

Lifting the Lid off the Furnace

The Molten Bronze is Lifted Out of the Furnace in a Container Called a Crucible

Molten Bronze Hoisted out of the Furnace

Molten Bronze Hoisted out of the Furnace

Molten Bronze in the Crucible

Molten Bronze Poured from the Crucible into the Two-Part Sand Mold

Molten Bronze Cools in the Two-Part Sand Mold: Weights are Placed on Top to Contain the Hydraulic Pressure Created in the Mold

After About 20 Minutes, the Bronze has Cooled Enough to be Released from the Two-Part Sand Mold

Bronze Casting Released from the Two-Part Sand Mold

The Final Product: A Cast Bronze Plaque

Laser cutting is a great technique for quick fabrication, in part because of the very small point size of the laser beam. The minuscule kerf of a laser cut allows for very tight 90° angles on interior (and exterior cuts).  This makes it easy to laser-cut thin panels of material for joining, as oomout demonstrates in this post on instructables.com (example pictured below). One of the drawbacks of laser cutting is the limited depth of materials that can be successfully through-cut; the laser cutter that I have access to can get through about 1/2″ of MDF or plywood, but the cuts are very charred and not perpendicular due to the hourglass shape of the laser’s focal point.

T-Bolt connection using laser-cut 1/4" panels

CNC routing is another great technique for quick fabrication. The range of material depth is much greater, there’s no burning, and through-cuts are perpendicular. One of the biggest drawbacks, however, is the inability to route interior corners due to the cylindrical shape of the cutting tool. This can require tedious hand-finishing to file or chisel out the interior corners to 90° angles, which is not worthwhile for projects that don’t have to look pretty, i.e. prototypes.

The technique pictured above is achieved by simply routing an extra bit of material out of interior corners to allow for 90° butt-joints. To set the paths for the corner knock-outs, a circle is created at each interior corner using a 3-point definition; the first point is set on the corner’s intersection, the second two are placed on each edge of the corner at a distance equal to the diameter of the router bit you plan on using. This will make sure enough material is taken away to allow for a 90° joint.

Vector path for 1/4″ laser-cut t-bolt joint (.dxf)

Vector path for 1/2″ CNC-routed t-bolt joint (.dxf)

Colors in the screenshots are only intended to distinguish between steps. Enjoy!

The final product should look something like this Webcam file with all steps (.3dm, 16mb)
Step 1.a Start a new file (small obj/inches)
Step 1.b In the Top viewport, draw 2 concentric circles, centered on 0, 1″ and 2″ diameters respectively.
Step 2 Copy and paste the smaller circle in place.
Step 3 Turn on Osnap and activate Cen only. Activate Move command, snap to Cen of copied small circle, then type <45 to add an angle constraint.
Step 4 Move small circle outward so that it intersects with the outer circle.
Step 5 Activate the ArrayPolar command. Select the small circle to array. Set 0 as the center of the array. Set the number of items to 4. Set the angle to 360. Hit Enter.
Step 6.a Select the four small circles. Activate the Split command, and split the large circle.
Step 6.b Select the large circle, then activate the Split command and split the four smaller circles.
Step 7 Select the four larger segments of the outer circle, and the four smaller segments of the outer circles–they’ll form a rounded cross-shape. Join these curves with the Join command.
Step 8 Turn on grid snapping. Select the innermost circle, and move it up one inch in the RIght or Front viewport by clicking and dragging.
Step 9 In the Front viewport, turn on grid Snap. Activate the Interpolate Points curve tool. To draw the first point, snap to the grid intersection on the x axis that is two inches to the right of zero. Then turn Snap off. Draw a line that is the approximate shape shown – it does not have to match perfectly. To draw the last point, turn Snap back on, and snap to the grid intersection that is 1″ above the x-axis and 1″ to the right of the z-axis.
Step 10 Select the curve you just drew, then activate the Offset command. Set the Distance to 0.04″, and offset below the original curve.

I’ve found this technique to be really useful for making quick, cheap mock-ups of 3D models, as well as getting some really interesting visual results for artmaking.

The first of the two main techniques I’ve been using is ’slicing’ models in Rhino using the Contour command, then exporting the curves to Illustrator. The curves are cut out of flat material (usually cardboard or acrylic) on the laser cutter, then re-assembled with glue into a mock-up of the 3D model.

This technique results in an economical model relatively quickly, and allows you a lot of flexibility compared to ‘unfolding’ techniques such as those used with Pepakura. It can, however, be quite tedious to re-assemble all the slices in the proper order/orientation. It is also not the most accurate method, as the shape of the model depends on the orientation of our curves in Rhino matching the orientation of the cut slices.

I’ve written a couple of scripts that take a lot of the grunt-work out of processing files. They are free for you [and everyone] to use. Also, keep in mind that the laser cutter part of the equation is optional. The contours can be cut by hand, although it will be a much bigger pain in the ass.

Here is the basic technique:

In Rhino:

• Create a 3D model in Rhino. It helps if the model is solid (aka a joined polysurface, aka watertight)
• Create topological contour curves of the model using the Contour command. The contours can go in any direction, and the spacing should be equal to the depth of the material you’ll be using.
• Group the curves: use the PlanarSrf command to create surfaces from each ‘level’ of slices. This accounts for contours which are donut-shaped, such as those that would come from a tube or bowl shape. These concentric curves must be grouped together to maintian the profile of the 3D model.
• Flatten the surfaces: use the UnrollSrf command to align each surface to the top viewport. This will prevent the curves from being distorted upon export.
• Convert back to curves: use the Make2D command to transform each surface back into the original curves. This prevents the need for extra editing once the curves are brought into Illustrator.
• Export the curves as Illustrator files (*.ai). Preserve the scale, but since Illustrator does everything in points, convert to points (1 inch = 72 points). This will ensure the scale of the 3D model is preserved.

In Illustrator:

• Open each curve file that we just exported from Rhino.
• Move each curve or set of curves into its own layer in a file that has been templated for the laser cutter.
• Arrange and format the curves, then send them to the laser cutter.

On the laser cutter:

• Use the least amount of material possible.
• Keep track of the pieces you’re cutting out. Numbers can be engraved by the laser cutter, or the cutouts can be kept in their original position and compared to the files.

In real life:

• Assemble the slices, using numbers and/or Illustrator files and/or the Rhino model.
• Bask in the glory.

The Scripts:

These scripts are distributed under a Creative Commons Attribution Noncommercial Share Alike 3.0 License. You must follow the terms of this license if you wish to use these scripts.

Please see http://creativecommons.org/licenses/by-nc-sa/3.0/ for details.

These scripts are not intended to do anything malicious, however I take no responsibility for any ill effects caused by these scripts. If you have any questions about the way these scripts work, please feel free to ask prior to running them.

• Rhino: gen_conts_flat_export_WORKING.rvb
• Illustrator: curve_arranger_working.js

Resources:

• Scripting Adobe Applications – User to User Forums
• Illustrator CS Scripting – Getting Started With Javascript [pdf]
• Rhino Scripting [pdf]
• Rhino Scripting Tutorials